A good understanding of theories of failure are imperative in the design of civil structures or types of mechanical equipment. This lecture will give you a conceptual introduction on the theories of failure. So sit back and Enjoy
A detailed webpage version of the above lecture along with the industrial application of Failure Theories are given below.
The Weight Lifter Analogy
Consider a weight lifter problem.
|Fig.1 A weight lifter analogy|
In the first case he is able to lift maximum up to 50 k.g in a relatively simple fashion. Now consider a second case, here he is lifting the same amount of weight in a different manner.Is it true to say here also his maximum lifting ability is 50 k.g?. Answer to this question could be Yes or No. If you assume that, his lifting ability is same in the second case also , then this can be considered as a failure theory for a weight lifter.
The Backbone of Failure Theories
In materials also we can apply the same concept of weight lifter failure theory.Here material will undergo a simple force test(simple tension test), so one can determine what’s the maximum load capability the material has. Now, we will assume that in a complex loading condition also, the material has the same capability. This assumption forms the backbone of Failure theories.Concepts of Simple tension test and Principal stresses are the main 2 prerequisites to understand the Failure theories effectively.
Simple Tension Test
In Simple tension test material is pulled from both the ends, the elongation of material(strain) with respect to the load is noted. From such an observation one can easily determine maximum strength of the material. For ductile material upper yield point is considered to be maximum strength of material, while for brittle material it is taken as ultimate strength of the material. From the maximum strength value of the material, values of various other parameters can easily be calculated.Simple tension graph and upper yield point value for a ductile material case is shown in the figure below.
Fig.2 Simple tension test
Once you know Principal stress values you can go ahead with failure theories.Figure below shows principal stress values induced at point in a 3 dimensional complex loading case.
Fig.3 Principal stresses and planes
The Failure Theories
The interesting thing in the Failure theories is that, just by looking at the name of the theory you will be able to formulate condition of failure in an actual case. Just make sure that your concept of STT and Principal stresses are clear. The theories along with its usability is given below.
- Maximum principal stress theory – Good for brittle materials*
- Maximum shear stress theory – Good for ductile materials
- Maximum normal strain theory – Not recommended
- Total strain energy theory – Good for ductile material
- Shear strain energy theory – Highly recommended
According to this theory when the maximum principal stress induced in a material under complex load condition exceeds the maximum normal strength in a simple tension test the material fails. So the failure condition can be expressed as
According to this theory when the maximum shear strength in actual case exceeds maximum allowable shear stress in simple tension test the material case. Maximum shear stress in actual case in represented as
Maximum shear stress in simple tension case occurs at angle 45 with load, so maximum shear strength in a simple tension case can be represented as
Comparing these 2 quantities one can write the failure condition as
This theory states that, when the maximum normal strain in actual case is more than maximum normal strain occurred in simple tension test case the material fails. The maximum normal strain in actual case is given by
Maximum strain in simple tension test case is given by
So condition of failure according to this theory is
Where E is Youngs modulus of the material
According to this theory when the total strain energy in actual case exceeds the total strain energy in simple tension test at the time of failure, the material fails. The total strain energy in actual case is given by
The total strain energy in simple tension test at time of failure is given by
So failure condition can be simplified as
According to this theory when the shear strain energy in the actual case exceeds shear strain energy in simple tension test at the time of failure the material fails. Shear strain energy in the actual case is given by
Shear strain energy in simple tension test at the time of failure is given by
So the failure condition can be deduced as
Where G is shear modulus of the material
Out of the 5 theories discussed, the Shear strain energy theory or Von-mises theory is the most valuable one.
*Since brittle materials does not have yield point, you can use ultimate tensile stress as failure criterion.
Industrial Applications of Failure Theories
Nowadays FEA based solvers are well integrated to use failure theories. User can specify kind of failure criterion in his solution method. Shear strain energy theory is the most commonly used method. These softwares can produce Von-mises stress along material,which is based on Shear strain energy theory.
So user can check whether maximum Von-mises stress induced in the body crosses maximum allowable stress value. It is a common practice to introduce Factor of Safety(F.S) while designing, in order to take care of worst loading scenario. So the engineer can say his design is safe if following condition satisfies.